VoyForums
[ Show ]
Support VoyForums
[ Shrink ]
VoyForums Announcement: Programming and providing support for this service has been a labor of love since 1997. We are one of the few services online who values our users' privacy, and have never sold your information. We have even fought hard to defend your privacy in legal cases; however, we've done it with almost no financial support -- paying out of pocket to continue providing the service. Due to the issues imposed on us by advertisers, we also stopped hosting most ads on the forums many years ago. We hope you appreciate our efforts.

Show your support by donating any amount. (Note: We are still technically a for-profit company, so your contribution is not tax-deductible.) PayPal Acct: Feedback:

Donate to VoyForums (PayPal):

[ Login ] [ Contact Forum Admin ] [ Main index ] [ Post a new message ] [ Search | Check update time | Archives: [1] ]

[ Next Thread | Previous Thread | Next Message | Previous Message ]

Date Posted: 14:05:38 02/05/02 Tue
Author: Sash
Subject: Re: Need Help with AVR4 No Cam
In reply to: Jim 's message, "Re: Need Help with AVR4 No Cam" on 21:56:14 02/04/02 Mon

When i use JeepersDX and do a full monty(no cam, with my box keys), i get the 020 error, The smart card Currently inserted is not valid for use with this receiver.

We're close i can feel it :)

Thanks

Sash

>Ok,You have an AVR4 no cam,(You will need Box Keys)no
>autoroll,
>I would just run JeepersDX ,Fill in all Fields and do
>Full Monty.there is no need to run 12C program because
>you don't have extra chip
>Let use know if it works
>
>>That's the step i couldn't do, everytime i tried to
>>program my I2C in Jeepers(1.2.1) or JeepersDX, it does
>>the bootloader part fine but for the next part the
>>progress bar dosen't move.
>>I tried with 128 and 256.
>>
>>Again, my AVR4 only has the large rectangular S8515
>>with pins 10-12 jumpered.
>>Do i need any extras on it or this setup is ok ?
>>
>>Thanks again for all your help :)
>>
>>Sash
>>
>>>Yes,you will need to use Jeepers to program 12C (i'm
>>>assuming you know how to use Jeepers) then program
>>>8515 with Nawapoc3 again.Hope it works
>>>
>>>
>>>>I just tried, still no go :(
>>>>
>>>>With this type of AVR4, do you still need to go into
>>>>Jeepers to program your I2C ? I don't think so but i
>>>>wanted to make sure.
>>>>
>>>>>Have you tryed cleaning AVR contacts (silver
>squares
>>>>>on back side of AVR) with an eraser.Might help
>>>>>
>>>>>>I have an AVR4 and it used to work perfectly
>before
>>>>>>the 02 cmd, now i cant get it to work at all with
>>>the
>>>>>>new procedure.
>>>>>>
>>>>>>I followed the new instructions to the letter,
>>>>>>generated my eepgen file, edited it to make sure
>it
>>>>>>was ok and sure thing, everything seemed fine.
>>>>>>
>>>>>>Ran funprom with those 2 files, the flashfile
>>>>>>nawapoc3.hex and my generated file as int.
>>>>>>
>>>>>>Problem is, i get no picture at all and the
>>>'aquiring
>>>>>>signal' never appears.
>>>>>>After like 15 mins the msg ' Card not properly
>>>>>>inserted' pops up and that's as far as it goes.
>>>>>>
>>>>>>What am i doing wrong ?
>>>>>>
>>>>>>Card Info : AVR4 S8515
>>>>>>That's the large rectangular chip.
>>>>>>pins 10 and 12 jumpered
>>>>>>it dosen't have the extra chip on it
>>>>>>
>>>>>>Need help !
>>>>>>
>>>>>>Thanks in advance
>>>>>>
>>>>>>Sash

[ Next Thread | Previous Thread | Next Message | Previous Message ]

Replies:

[ Contact Forum Admin ]

Forum timezone: GMT-4
VF Version: 3.00b, ConfDB:
Before posting please read our privacy policy.
VoyForums(tm) is a Free Service from Voyager Info-Systems.
Copyright © 1998-2019 Voyager Info-Systems. All Rights Reserved.